reduced friction Germany

...TIPP OIL Super Ultra 5W-30 is a synthetic low-friction engine oil with reduced sulfated ash content, suitable for passenger car gasoline and diesel engines. It is particularly designed for the latest diesel engines equipped with particulate filters. TIPP OIL Super Ultra 5W-30 is characterized by excellent cold-start properties, minimizing fuel consumption, friction, and wear. With a lowered HTHS...

...Surface treatment with laser with a broad spectrum of applications (improved thermal conductivity, anti-icing / freezing, anti-friction, anti-wear, lubrication, anti-microbial, reduced electrical resistance e.g. for connectors, holograms, product protection, logos, wettability, increase surface area by up to 280% ...). Can be used for metal (steel, aluminum, titanium) polymers / plastics (e.g. polycarbonate), composite material and ceramics...

...TS421 consists of technical thermoplastics specifically designed for extremely low friction under lubrication conditions with reduced loads.

... eliminates wear caused by metallic friction in any operating state, even at zero speed compared to hydrodynamic plain bearings. In conjunction with highly dynamic control valves and angle of rotation sensors, these actuators are preferably used in controlled systems in which disturbance variables such as friction and the stick-slip effect must be reduced to a minimum. Furthermore, due to the lack...

The increasing use of three-dimensional components made from polymer materials with lower surface energy prompted manufacturers of pretreatment systems in the 1980s and 1990s to explore new avenues. While previously only the employed Corona technology was available for two-dimensional sheet goods, fluorination emerged as a suitable method for activating even complex three-dimensional molded parts.

... weight of 290 - 300 kg. For a staple leg length of 25 mm, this results in approximately 5.2 million staples for a wire thickness of 0.60 mm. …torsion-free operation due to the special winding and correspondingly low pulling forces during wire extraction. …minimized friction of the staple wire in the stapling tools, resulting in fewer mis-staples and reduced wear.

...Show product variants Ceramic Additive High-performance additive package with ceramic to enhance wear protection properties. Increases operational safety in high-temperature ranges. Saves fuel. Reduces exhaust emissions. Features: • saves fuel • more torque • reduces friction • reduces wear • reduces running noise • stability of the lubricant film due to lower oil temperatures • reduced exhaust values Areas of application: Suitable for all engines. Container: Drum Country of origin: Germany Content: 200 liters...

... Coefficient of friction only 10% higher than in iglidur® J Coefficients of friction identically exceptional like iglidur® J Reduced installation space as well as easy and simple mounting Realizable with numerous sealing types High-temperature option VDSM possible Temperatures till 150° C Material: iglidur® J High temperature option VATM, iglidur® V400 Seal ring made of fluorelastomer Bearing-sealing...

... lubricant formula Broad range of uses above normal grease performance areas Reduced maintenance and lubricant costs due to possible safety lubrication Drip-free hot bearing grease for long-term and safety lubrication in a broad temperature range For best results clean the lubricating point carefully. Clean with solvents like OKS 2610/OKS 2611 Universal Cleaner. Remove the corrosion protection ahead of...

... - structures and surface coatings tailored to requirements and electrostatic properties - damping properties suited to needs (depending on the traction layer) - low installation tension, significantly reduced load on shafts...

... capacity, robust and resistant to dirt. Suitable for grease or oil lubrication and all kinds of movement, good load capacity, robust and insensible to dirt. For technical details, please visit the product page on our website! Support material/Carrier material:Tin-plated steel (1.0330) Intermediate layer:Sintered bronze Sliding layer:Acetal resin / POM Static load:≤ 250 N/mm² Dynamic load:≤ 140 N/mm² Sliding speed:≤ 2,5 m/s Friction value:0,04 to 0,12 µ Temperature strain:–40 bis +130 °C Max. PV-value:2,8 N/mm² x m/s Housing Ø:H7 Bushing inner-Ø after mounting:D9 to D10 Shaft tolerance:h8...

...During the production of a protective cover for a shot blasting robot, a thorough technical analysis of the constraints the robot is subjected to is required. This analysis is carried out by experienced technicians from the ASP department dedicated to methods in collaboration with the technical-commercial staff, in order to address each individual customer case. High-quality ASP protective covers fully protect the robot during its operational process, allowing for reduced operations and high maintenance costs.

... buildup and wire breakage from incorrect contact with the teeth of the drive wheels is avoided. The characteristic recess of the Clean-Sweep™ is milled into the gears to reduce drive friction from product deposits and extend the lifespan of the belt. We offer you various complete packages of consumables.

... support structure made of lightweight aluminum with low-friction plastic guides ensures smooth operation through precise roller bearings - Acceleration up to 1 G, speeds up to 60 m/min - Extension ratio of 10:1 Benefits: - Up to 9000 mm of free span width with minimal deflection - Individual folding segments are interchangeable - Folding depth and folding direction are variable (folds can be chosen to go up or down) for more space beneath the cover.

...Through our surface treatment, elastomers experience an increase in the hardness of the sealing surface. Friction is reduced, thus facilitating assembly. Surface Modification: The surface of the elastomer is modified in this process through a chemical reaction with a process gas at the micrometer level. The physical properties of the elastomer are hardly affected. Assembly Facilitation / Assembly Aid: Assembly and joining forces are reduced, making the installation of seals easier. It prevents sticking in packaging or during the assembly of elastomer seals.

...BRECOFLEXmove belts operate in high-performance drives and traction drives with the highest stiffness requirements. The BRECOmove meter goods are used in linear technology. Compact design, reduced friction, and increased power transmission: Specifically developed for high-performance drives and traction drives with the highest stiffness requirements, the polyurethane belt BRECOFLEXmove can...

... good wear protection of Castrol High Temperature Grease goes far beyond the standard of conventional lubricating greases. These good properties result from the effectiveness of the innovative additive package developed specifically for Castrol High Temperature Grease . By smoothing the surface roughness on the friction surfaces , their load share increases . This creates increased safety with regard to the load capacity of the bearings with reduced friction. Product number:1965718 Container size:1 Product group:Industry...

... necessary. Prevention of dents Thanks to the high friction of the secutex material, the coil cannot slip and, in some cases, the contact pressure can be significantly reduced. The typical impressions in the initial winding layers are prevented and material wastage is significantly reduced. The secutex material is extremely wearresistant and, unlike standard rubber, is also oilresistant. The insertion tip helps thread the coils. ...

... • Large clamping range • Reduced variety of variants • Optimal hole filling and pronounced hole friction • Well-suited for transferring shear forces with moderate clamping force • Ideal for applications in: — LED light strips — Electronics/PCB assembly — Lightweight sheet metal constructions — PC cases — Nameplates — Blind hole drilling...

...Our polymeroxid®-LF4 process is an innovative anodic special coating for applications where surface smoothness is paramount. In this process, the friction properties have been further optimized, with a slightly reduced hardness compared to xH4®. When using suitable materials, excellent decorative qualities can be achieved, opening up new application possibilities where hard anodizing was...

...ERC motor oil power additive with friction modifier reduces friction, wear, and sediments. It also improves the oil supply and stabilises viscosity with reduced oil sludge formation. All these features contribute to improved engine performance. THE EFFECT With the ageing of oil in everyday engine operation, build-up and clogging of filters and oil passages occur. ERC motor oil power additive...

...reduced shaft wear and excellent heat transfer characteristics Thermally balanced construction, the coefficient of expansion is similar to steel, the packing is volume stabile and does not shrink. Therefore minimal re-adjustment needed after installation. Excellent chemical resistance Recommended shaft surface hardness: HRC 45 Operating range Pressure [p max]: 30 bar, Velocity [v max]: 25 m/s Pressure [p max]: 100 bar, Velocity [v max]: 2 m/s Pressure [p max]: 100 bar Temperature: t = -50… +300 °C pH: 2 - 12 Density: 1.45 g/cm³ Practical useful application data: max. temperature: +250...

...LUBERO - Tools that deliver real performance Machine tap drills require not only the right material, hardness, and toughness but also a perfectly ground cutting geometry. When this is further enhanced with a higher surface hardness and reduced friction through an appropriate coating, you get genuine LUBERO high-performance taps. They are ready to compete with anyone in terms of tool life and cutting results, providing our customers with real added value in the form of speed and endurance.

...Shaft seal as an alternative to DIN 3760 with reduced radial force and increased speeds The Prelon ring MR is characterized by particularly smooth operation, low wear, and pressure resistance. The omission of a worm spring and the associated material accumulation allows for a significant reduction in the contact pressure on the shaft. In combination with particularly low-friction elastomers, the friction moment is reduced by 50 to over 70% compared to shaft seals according to DIN 3760. Consequently, the heat generation and power loss are also minimal.

...VICTOR Ceramic Engine Protection Is a high-performance additive designed for use in all engines without wet clutches. An effective additive package with wear-resistant ceramic to reduce friction and improve wear protection properties. Suitable for all mineral and synthetic oils. Benefits: Only optimal lubrication guarantees minimal wear and a long lifespan for engines and units! Simple, universal application. Reduces operational noise, friction, and wear, while ensuring higher engine performance, optimized fuel consumption, and reduced exhaust emissions.

...The combination of rings made from chrome steel and rolling elements made from ceramic, such as SI3N4. Higher rotational speed capability. Low friction. Minimal wear. Reduced deformation tendency. Electrically insulating. Special requirements demand special solutions. In the field of hybrid and fully ceramic rolling bearings, BEARING SERVICE offers technically excellent yet particularly...

... 3408-1). Compared to conventional screw drives with sliding parts, where about 50 to 90% of the input power is converted into heat, ball screw drives offer: less friction (lower drive power, greater possible movement speed), reduced stick-slip behavior (higher positioning accuracy), and lower wear. The higher manufacturing costs are offset by advantages in use and a longer lifespan. Weight: 2.0 kg/m Length: freely selectable up to 3 m...

...Forklift Cross Conveyors These are primarily used for transporting sheets or flat materials that experience deflection due to their own weight. However, their use is also sensible for heavy profiles due to the significantly reduced driving forces from rolling friction and the elimination of noise. All forklift cross conveyors require continuous solid support rails for placing the material, which...

... available with standard end machining or with end machining according to customer specifications. Due to the low rolling friction and the suppressed breakaway torque, a high mechanical efficiency of 98% is achieved, thereby reducing the required drive power. Based on decades of continuous development of the raceway profiles and the deflection systems in the ball screw nuts, NEFF ball screws stand for exceptionally high quality and longevity.

... extended as well as the operating conditions significantly improved. Further advantages no jammed rollers causing belt misalignment absorb the drop energy, support the conveyor belt instead of the conveyor rollers in the transport area of the conveyor system and make a reliable running of the belt possible whilst ensuring the least possible friction. infinitely variable alignment to the angle of inclination by means of spindle displacement possible better material sealing due to adjustment of the material guide to within a millimetre...