liquids Germany

...AViTEQ drainage screens are designed as linear vibrators and are used for draining sand, plastic granulate, kieserite, limestone, coal, etc. They are also used for separating insoluble impurities from wash water or carrier liquids. Advantages and Benefits • double, specific screening performance of the linear vibrator compared to flat screens • easy replacement of screen media • low construction...

...Inks PINK • available from 28 to 60 mN/m in 1 mN/m increments • Accuracy +/- 0.5 mN/m • Reading time from 28 to 60 mN/m: 4 sec. The test inks PINK are test liquids with defined surface tension, dyed pink. They have been specifically developed to offer non-toxic test inks. These PINK test inks can be used as a substitute for the BLUE test inks, as their application and handling are based on DIN 53364 and ISO 8296. The PINK test inks are available in bottles or in pen form.

...The capacitive level sensor NR 160 is designed to monitor liquids and powders with high relative dielectric constant εr 35 … 85. The functions for MIN or MAX monitoring as well as other properties (output signal LSS or HSS, response delay etc.) are factory pre-set. The switch point is adjustable by means of a teach-in momentary switch.

...EGE's capacitive level sensors are designed to reliably monitor the filling level of granules, powders, solids such as springs, liquids, and aggressive or adhesive fluids. The fluid to be detected acts as a dielectric. The fluid in contact with the sensor generates a change in capacitance. This change is converted into a switching signal or an analog output signal of 4...20 mA. The level sensors...

...Our patented closed suction pads DIM Premium: With the highest hygiene standards Absorbent core made from tested airlaid All-around food-safe film with only one weld seam Liquid absorption through perforation of the film Liquids remain securely enclosed High liquid absorption through patented process Large active absorption areas (no seam protrusions at the side edges) Safe detection of cross...

...A shut-off valve is used to regulate or stop the flow of liquids in a pipeline. Shut-off valves are designed for manual operation and can be opened or closed by turning a handle or lever. When the shut-off valve is open, the liquid flows freely through the pipeline, and when it is closed, the flow is stopped. Shut-off valves are often used in emergencies to quickly stop the liquid flow in the...

...Industrial pressure measurement covers a very wide range of gases and liquids. The physical and chemical properties of these products sometimes make them incompatible for contact with the sensing elements of pressure gauges or transmitters. In such cases the measuring instrument must be separated from the pressurized fluid by a system capable of transmitting the pressure to this instrument...

...Everyone knows that the key to a long and and troubleless operation of the engine is the use of high-quality motor oils and lubricants that meet the requirements of the vehicle manufacturer and its timely replacement. Buying oil and technical liquids from us, you can be confident in the quality of purchased products; then, our company is the official partner of such leading brands as CASTROL, MOTUL, VENOL, which is confirmed by the corresponding certificates. Our experts will help you choose lubricants, and prices will surprise even the most discerning buyer.

...Resistant customized dosing pump The micro annular gear pump mzr-2542 of the modular series is suitable for dispensing and metering of aggressive or corrosive liquids. Equipped with oxide ceramic bearings, the material configuration of the pump body as well as of the rotors can be individually selected. Depending on the nature of the delivered liquid, a choice of different resistant components...

... way, no pressure differences are brought to bear on the foodstuff during the creation of the vacuum. Foodstuffs with a high liquid content and even entire liquids (soups, sauces, etc) can be processed in this way. Once sealed aromas, nutrients, vitamins as well as the cell structure and nutritional juices remain unaltered the foodstuffs are optimally prepared for sous-vide cooking methods the efficient absorption of spicy aromas is guaranteed with sous-vide cooking in a bain-marie or a steamer ingredients remain fresh up to three times longer when in the...

... provides the ideal conditions for your bearing constructions. Use in dry environments as well as in liquids is possible. Type of lubrication: self-lubricating, maintenance-free Alloy SL-2 - CuAl10Ni Temperature range: -200 to +400 °C Max. sliding speed: 0.5 m/s Max. PV value: 1.5 MPa m/s Max. dynamic surface pressure: 120 MPa Max. static surface pressure: 225 MPa Alloy: SL-2 - CuAl10Ni Temperature range: -200 to +400 °C Max. sliding speed: 0.5 m/s Max. PV value: 1.5 MPa m/s Max. dynamic surface pressure: 120 MPa Max. static surface pressure: 225 MPa...

...ASP’s "Foundry – preparation area" covers use non-woven foil (FPE) or fabrics coated on one or two sides. These specific coatings provide the mechanical properties that these processes require (abrasion resistance, high tear strength, etc.). The "sealed seams" option further improves reliability by offering protection from liquids (water, resin, etc.). Covers that are tailor-made and repaired in our workshop provide the best protection for your robots. ...

...We classify all precious metal-containing sludges, powders, and liquids that are formed as residues of an electroplating process into the category of galvanic waste. Since these mixtures often contain highly concentrated acids or alkalis, they must be transported, stored, and processed with special care regarding these hazardous materials.

...Electrical process flow heaters The “STR type electrical process flow heater comprise a large range for industrial application custom built to meet client specification. These heaters are supplied CE marked in acc. the latest CENELEC requirements or manufactured to the latest IEC standards. Typical electric process heaters applications include heating of liquids i.e. heat transfer oil or fuel oil, glycol reboilers and water heaters and heating of pressurized gases i.e. pressurized air, superheated water steam, nitrogen or other compositions of gases.

...Single-use syringes for medical purposes as well as for drawing up liquids or injecting liquids immediately after filling Item number: 534200[PCK100] Features: U-40 and 1ml EAN: 4036534200025 Unit: U-40 Size: 26G x 1/2" (0.45 mm x 12 mm) Piston: White Material: Polypropylene Needle connection: Luer lock, concentric Quality standards: Compliant with 1997 and EN ISO 7864:1995 - Manufactured according to MPG Directive 93/42/EEC - amended by Sterility: Sterile by ethylene oxide Type: 3-part Sales unit (VKE): Box, 100 pieces per box (individually packaged) Volume: 1.0 ml...

...Designing pumps, compressors and other equipment, the aim is to prevent leakage into that can emerge at any point by liquids or gases. To solve this problem very often are used mechanical seals. To obtain the desired sealing function and an adequate lifetime of the mechanical seal,the preconditions must be fulfilled within the permitted tolerances at any time: parallelism of the sealing...

...Current Situation Seals are a key component in many industries and are often used in safety-critical areas. They require two relatively flat surfaces to prevent the leakage of media such as gas or liquids. Challenges: The sealing surfaces are often made of highly polished metal. This can create reflections that need to be eliminated during optical measurement. SourceTech Solution The Q5 laser...

...Short description: PVC flat hose, medium weight Layflat hose, medium-weight construction, for delivery of liquids under pressure, flat rollable. Agricultural irrigation, construction industries, mining and industry in general. Norm::ISO 1307 Temperature range::-5°C to +60 °C Standard length::50 m Colour::Blue Cover::PVC Reinforcement::Polyester yarn Lining::PVC, smooth, black...

...Vegan HPMC, gelatin, and enteric-coated capsules ranging from size 3 to 000. As a full-service contract manufacturer for dietary supplements, we leave no wish unfulfilled. Whether hard capsules, softgel capsules, tablets, powders, liquids, or special formulations, we offer the full range without compromise. Through research on market developments and trends and access to a broad network of international, renowned raw material suppliers, we regularly expand our portfolio to provide you with the best possible advice and support in choosing the right product for your portfolio.

...Speck-Triplex offers system solutions for a wide range of applications. According to customer specifications, complete high-pressure units and pumping systems are manufactured with Speck high-pressure plunger pumps for various applications involving liquid media. Options in brass, spheroidal graphite, bronze, NiALBz (marine-grade), 1.4301 (AISI 304), or 1.4571 (AISI 316) for aggressive liquids are available. The sealing materials are tailored to the specific application. All components are high-quality branded products.

...SternMaid has established a reputation for quality in the mixing of powdered substances. With passion, expertise, and cutting-edge technology, we fulfill your mixing orders. We mix and refine batch sizes ranging from 50 to 4,000 liters, which corresponds to an average of 25 to 2,000 kilograms. We also possess the exact know-how for premixes or trial blends. All mixing systems are frequency-controlled and carry out your project gently in short mixing times. For intensive mixing or grinding, we use knife heads that also allow for the incorporation of liquids and the dissolution of clumps.

...These devices are suitabele for transportigng heavy loads of up to 1300 kg, overcoming obstacles such stairs, ramps and tailboards. Also for loads containing liquids such as fridges & co. Heavy loads (such as switch an server abinets, safes, boilers, parts of mchinery and systems, etc.) can therefore be delivered down or up stairs, even by a single person.

... Applications: - for gases and liquids - chemical industry - food technology - pharmaceuticals Delivery forms: - Ø 3 to 20 mm, up to 25 m/roll - Color: opaque inside, red outside On request: - short lengths - customized to customer specifications with fittings... - SilPress tt - transparent inside and outside...

...Screw-in Tubular Heaters are the standard solution for all heating processes with liquids or gas. The heater is installed in a tank or a tube system by the G1½" screw fitting. The IP54 connection head, fitting and tubular heater consists of stainless steel. The tube sheath material 1.4529 is resistant to sulphite, phosphors and hydrochloride media. Type:without controller and limiter Type:with controller (adjustable from 30 ° to 85 °C, freezing protection at 7 °C) Type:with limiter (adjusted to 110 °C) Type:with controller-limiter-combination...

... longitudinal seam on the back. We can package thin liquids, pastes, and free-flowing media for you. They can be elaborately printed (up to 8 colors), making them eye-catching for your customers, or produced with a cost-effective thermal transfer print for factory use. In special cases, a degassing hole can be added. Tube bags are a cost-effective packaging solution. Print: 1 - 8 colors. Special feature: Pastes and granules) - Degassing hole can be added. Size: from 60x90 to 140x220 mm.

... ingredients, matrix encapsulation relies on a different process where liquids or the finest powders are mixed with the carrier component – the matrix – in the fluidized bed, ensuring that the active ingredients are evenly distributed within the particles. The resulting particles can achieve active ingredient loadings of up to 50–60% without compromising flowability. Up to 50–60% liquid loading: Gentle drying of sensitive components Specific controlled-release mechanisms: Particles suitable for tableting...

... In the food industry the atomisers and dosing systems of Mantis can be used everywhere where liquids have to applied uniformly and sparingly. This could for example be the application of release agents onto baking trays and dishes or the application of flavouring substances. Don’t hesitate to contact us! We offer an optimally adjusted spraying system also for your application area!

...with a large filling opening for packaging and storage of liquids, powders, and granules. Material: HDPE; Standard color: white and natural; Volume: 50 - 2500 ml; Thread: 40 - 80 mm;...

...Hydrostatic bearings are characterized by practically frictionless movement. The corresponding linear guides are free from stick-slip effects and there is practically no wear on the guides. Gases (mostly air) or liquids (mostly oil) can be used as the carrying medium. Air-bearing guides are ideal, for example, for clean room applications or at high sliding speeds. If oil is used as the carrying...

...The above mentioned filter bars are our standard designs. Here the end pieces are not sealed tight and therefore only suitable for dry applications. Not available ex stock, manufactured on demand Alternative to the standard we also offer individual solutions: » Seal-welded model for use in liquids (e.g. water, coolant) » High-quality stainless steel enclosure for use in food production » Increasing the max. operating temperature up to 350 °C » Manufacture of individual, not standardised sizes Article number:MS130NdSo00rh00 L mm:130 B mm:145 H mm:75 Temperature °C:80...