filter devices

...The filtration quality of this filter ensures clean air diffusion and an optimal working environment in accordance with CRAM requirements and your finishing needs. Composition 100% polyester fibers deeply impregnated with a binder. Clean air side reinforced with polyester mesh. Filtration category according to European standard EN 779 F5/M5 Information Standard dimensions 2m x 20m Other dimensions and cuts available upon request. Retention capacity: 326.50g/m² Filtration efficiency: 95.43% Recommended air flow: 0.25m/s Initial pressure drop: 26Pa...

... aerosol particles in the breathing air. The high-performance HEPA H13 filter removes potentially virus-laden aerosols from the room air. The cleaned air is then blown back into the room over the integrated long-range nozzles, ensuring that the purified air can be distributed up to 20 meters into the space.

... ensures a uniform flow across all bags. - Directing part of the gases to flow from top to bottom aids in the settling of dust in the filter chamber. - Dual positioning of filter bags by preventing their movement eliminates mechanical wear when the ends of the bags come into contact. This is particularly important when using long bags. - The use of a modern Twin-Jet regeneration system allows for the use of cleaned gas from the filter's clean chamber in this process. This increases the "strength" of regeneration while simultaneously reducing the consumption of external compressed air.

...Directly available for order, custom sinus filters for speeds up to 100,000 RPM, for three-phase networks, rated currents from 2.5 to 500 A. Sinus filters modify the PWM output voltage of frequency converters and produce a nearly sinusoidal voltage. The sinus filter variants with housing - "IG variants" - additionally feature a common mode choke to dampen high frequencies and common mode disturbances. The type series 3AFS400 is designed for use in 400 V networks.

...— Filtration of exhaust air flows caused by air displacement during the filling of dosing differential scales — Filter cartridge made of polyester fleece with a large filter surface area (FDA and GMP compliant) — Fully automatic compressed air pulse cleaning with the return of the filtered raw material into the production cycle — Sizes for containers up to over 1000 dm³ (35.3 ft³)...

...In the fight against smoke and fine dust particles, the NOVUS Airtower impresses with its air purification technology and effective welding fume filter. More than 99.5% of dirt particles disappear. Unlike conventional systems, the Airtower does not require ductwork, making it flexible to use. It is suitable for deployment in halls of all sizes. Optimized for the respective air volume flow, it is available in 4 performance levels.

BEKO TECHNOLOGIES represents compressed air and gas technology "at it's best". For over three decades, the company has been developing, manufacturing, and distributing high-quality, high-performance, and particularly efficient components and systems for the treatment of compressed air, gas, and condensate technology. Today, BEKO TECHNOLOGIES offers a comprehensive range for all tasks in compressed...

...• very compact in dimensions, making it easy to integrate into machines • the KFS is suitable for 19" racks • the high-quality EC motor is, of course, designed for continuous operation • safety guaranteed: automatic filter monitoring via differential pressure • dimensions 250 x 250 x 400 mm (L x W x H) Applications • very small welding and marking lasers • soldering fumes • adhesive vapors Maximum volume: 30-80 m³/h...

...RENNER filter devices are designed and constructed for use in chemical baths and processes. They have proven themselves in the circulation and cleaning of pure, slightly contaminated, or abrasive media, aqueous solutions, suspensions, or liquid mixtures. Our modular filter program offers a wide selection of freely combinable filter devices and complete filter systems for the removal of impurities through depth and surface filtration. The RENNER universal filter housings are equally suitable for accommodating: • Candle filters • Activated carbon • Filter bags • Filter plates...

it4ip exploits a unique and patented technology called "track etched" for the production of membranes with exceptional properties. These membranes consist of a thin, porous film that filters gases and liquids, and the expertise lies particularly in controlling the size and number of perforations created in them. This so-called "track-etching" technology allows for precise perforations ranging fr...

...The activated carbon filter FT-K is used for measuring critical pressure media or relative pressure media (overpressure or underpressure) with our devices when chemical compounds in the medium, such as SOx, HF, hexane C6H14, or others, need to be considered. The activated carbon filter FT-K is only suitable for filtering chemical compounds of low concentration in measurement lines without flow.

...The single cartridge filter is optimal for the efficient separation of heavily contaminated air with volumes up to 2000 m3/h, specifically for welding fumes as well as grinding and stone dust. With a stable and compact design, it can be easily installed in just 0.6 m2 of floor space, either next to or behind a machine. It is also ideal as a standalone solution for multiple small machines and workstations. The application areas are cross-industry: machining, grinding, welding, laser cutting, etc.

... handling sticky and moist dusts. The devices can handle high air flow rates and can be used as a central unit for multi-station extraction, enabling reliable extraction over greater distances. Additionally, they support low-contamination dust disposal and optionally provide high adsorption capacity through additional activated carbon granulate. Sound level: approx. 68 dB(A) Serial interface: 25-pin Sub-D Frequency: 50/60 Hz...

...The air purifier "air2000" is the medium-sized device in the air purifier series. It is suitable for extracting and cleaning air in spaces up to 150 m² and can filter up to 2400 m³/h of air. The device is equipped with a 5-stage filtration system and an integrated HEPA H14 filter element.

... contribute to process reliability. The dust generated during the blasting process is extracted by an airflow. It passes through the impact separator, where heavier dust particles are already separated out. Afterwards, it enters the lower filter chamber. Here, the filter cartridges are located. As the air flows through the filter cartridges, it is freed from dust and thus enters the clean gas chamber above in a purified state. At the same time, the filter cartridges are cleaned at adjustable time intervals by bursts of compressed air from the air nozzles positioned above.

...Folded filter cartridges in custom design Various polyester and polypropylene nonwovens are used as filter material. Support cores and cover discs can be made from plastic and/or metal depending on the application.

...An ATEX filter is a filtration device designed for use in areas where potentially explosive atmospheres may occur (ATEX zones). These filters must meet strict standards that ensure they will not ignite an explosive atmosphere through sparks or overheating. The components of these filters, including housings, filter elements, and cleaning systems, are all designed to withstand extreme conditions and to prevent the generation of ignition sources.

...Our modern flame protection filters Type B made of stainless steel (1.4301) direct the grease vapor inside the filter into a strong vortex where it condenses. From there, it flows into the grease channel of the hood, where it is safely stored until emptied. These Type B filters according to DIN 18869-5 must not be used above thermal devices with increased fire risk. Features of our flame...

... "standard construction site" to asbestos removal, even in hygiene-sensitive areas, and even in environments with clean rooms – all with a single device! This is made possible by the modularly combinable filters, with which you can create an optimal filtration circuit for any level of environmental contamination, but also and especially by the extraordinary Vario-Shift Function, which allows the HEPA filter to be applied to the device's terminal for use in clean rooms. Mounting: mobile Type: with HEPA filters Other features: low pressure...

...The SYCON SiO2 is an analysis device for monitoring silicate/silicic acid in a mixed bed filter. Monitoring of silicate in the ppm range (0.3 to 10 mg/l). Product Information SYCON SiO2 Monitoring of a freely programmable limit value Measurement of silicate content in the range of 0.3 to 10 mg/l Automatic zero point calibration before each measurement Graphical display, menu navigation in German...

... use (rubber protective frame) — Dust and splash-proof, suitable for use in high humidity — Intuitive user guidance through symbols — Color illuminated display — Battery level indicator — Error message in case of malfunction Scope of delivery: — Residual oxygen measuring device — Charging cable with adapter plugs for worldwide use — Hose set, 1 m, including filter and cannula — Calibration...

... contaminants. These air filters are made from pore-free aluminum with a durable epoxy coating and a corrosion-resistant inner coating for long-lasting performance. The filter combinations are configured to meet the specific application requirements. The filters comply with the PED and the relevant ISO 8573 standards. The filters can be equipped with differential pressure gauges to facilitate maintenance and improve energy efficiency.

... mask Standard EN149 Filteration Efficiency 99 Type medical mask Standard EN149 Filteration Efficiency 99:Melt-blown Fabric, 80% needle cotton ,20% nano melt blown filter material Type medical mask Standard Type medical mask Standard EN149 Filteration Efficiency 99:Melt-blown Fabric, 80% needle cotton ,20% nano melt blown filter material Type medical mask Standard...

...Filter regulator + oil maintenance unit of the compact series...

... responding to this with a comprehensive range of reliable filter devices. Special designs are also possible. Individual solutions for every need – that’s KOPP. Also in the area of ​​filter technology. Origin:Germany...

...Depending on the application, appropriate safety devices such as explosion pressure relief systems, extinguishing systems, mechanical and thermal monitoring systems, as well as pressure shock-resistant and ignition-proof rotary valves are provided. The PLC control system regulates and monitors the plants and safety technical devices. The filter housing in the standard version is tested for...

... Bolt, wireless and manual focus controllers from Arri and Oconnor Scorpio. Filter holders and filters from the best brands on the market in 4x4, 4x5.6, and 6x6, recorders from Odyssey, Atomos, Sound Devices, Magliners, and camera carts like Lince Crane, Easyrig, among others. We work with the best accessory brands to ensure your camera is well-equipped and nothing is missing. When renting, we advise on the best accessories required for your camera based on the type of shoot you will be conducting.

...High Performance Harmonic Filter Rated currents from 10 A to 400 A For power ratings up to 440 kW 380 V to 690 V (50 / 60 Hz), 3-phase THD-I up to 5% possible (typically 10-16%*) Specifically designed for devices with B6 bridge rectifiers Harmonic reduction up to the 50th harmonic (2.5 or 3.0 kHz) Switchable capacitors No leakage current For increased requirements * at R SCE ≥ 66, THD U ≤ 2%...

... possible while achieving the highest possible separation efficiency. This offers you the advantage of saving energy costs in the long run! Available are conventional IE2 motors as well as modern IE4 motors, which exceed all requirements regarding energy savings. A comprehensive range of accessories is available for all indusa dust filters to tailor the devices precisely to your application needs! 1. Type: DL 1100 N T JET JET: Cleaning with compressed air Dust bin: T - with dust bin...

...Single workstation extraction, extraction and filter devices for direct connection to an emission source such as machine tools. The devices require little space and can therefore be quickly and easily installed on a machine. The compact separators are particularly suitable for mounting on the machine casing.