Butterfly fire damper - FDA-BU
Butterfly fire damper - FDA-BUButterfly fire damper - FDA-BU

Butterfly fire damper - FDA-BU

The fire dampers are manufactured in the following nominal sizes DN100, DN125, DN160, DN200. The fire dampers are equipped with a thermal fuse mechanism ensuring the damper switch to the safe position in case of reaching an ambient temperature equal to or higher than 72°C. The fire dampers allow using limit switches signalling closed position of the damper blade (1 limit switch) or blades (in case of using 2 limit switches). The casing is made from galvanised steel sheet; the fire damper blade is made from a silicate cement board.
Similar products
1/15
Fire rated air valve with fire damper - FDA-BU-RML
Fire rated air valve with fire damper - FDA-BU-RML
The FDABURML coupling module is a combination of an air valve and a fire damper, coupled with a single housing. This is an alternative to typeical fir...
PL-05-552 Wola Mrokowska
CAV Constant air flow regulator 
 - RACAV
CAV Constant air flow regulator - RACAV
The RACAV constant air velocity regulator keeps the air output steady in ventilation systems. The device works without any electric power supply and f...
PL-05-552 Wola Mrokowska
Circular shut-off fire dampers with an actuator - FDA-12-M
Circular shut-off fire dampers with an actuator - FDA-12-M
The FDA12 round fire dampers are designed for use in general ventilation systems to seal off smoke and fire between adjacent fire partitions. The fire...
PL-05-552 Wola Mrokowska
Swirl diffuser - GCR
Swirl diffuser - GCR
GCR swirl diffuser is equipped with fixed blades bent at a constant angle. It is made of galvanized steel sheet, powder coated in RAL9010. Swirl diffu...
PL-05-552 Wola Mrokowska
PVC ducting - PVC-SRGL
PVC ducting - PVC-SRGL
Round plastic ventilation pipes are joined by welding (or PVC gluing up to ø250). Manufactured in accordance with DIN 8062 standards for ventilation p...
PL-05-552 Wola Mrokowska
EPP ventilation bend 15mm thick - EPP-15-BPF-45
EPP ventilation bend 15mm thick - EPP-15-BPF-45
Ventilation bends 45˚ made from expanded polypropylene (EPP). Bends are produced in diameters 125, 160 and 200 mm. The standard wall thickness is 15 m...
PL-05-552 Wola Mrokowska
Insulated EPP Plenum Boxes - EPP Plenum Boxes for Ø75 MVHR ducting
Insulated EPP Plenum Boxes - EPP Plenum Boxes for Ø75 MVHR ducting
The FLX-PLO-EPP-F plenum boxes are part of the FLX-REKU air distribution system designed for domestic mechanical ventilation systems, so-called the ...
PL-05-552 Wola Mrokowska
Energy recovery ventilator - HRU-SlimAIR-250E-H
Energy recovery ventilator - HRU-SlimAIR-250E-H
The HRUSlimAIR heat recovery unit is designed for residential buildings. The HRU has a capacity of 250 m3/h @ 100 Pa, generated by energyefficient EC ...
PL-05-552 Wola Mrokowska
Rectangular silencers - SLC
Rectangular silencers - SLC
The SLC and SRC rectangular duct silencers reduce the noise level in ventilation and A/C systems. This silencer type is usually installed between a fa...
PL-05-552 Wola Mrokowska
Polypropylene ductwork - PP-SRGL
Polypropylene ductwork - PP-SRGL
Round plastic ventilation pipes are joined by welding (or PVC gluing up to ø250). Manufactured in accordance with DIN 8062 standards for ventilation p...
PL-05-552 Wola Mrokowska
Round fire dampers with fusible link - FDA2-12-T
Round fire dampers with fusible link - FDA2-12-T
The FDA212 round fire dampers are designed for use in general ventilation systems to seal off smoke and fire between adjacent fire partitions. The fir...
PL-05-552 Wola Mrokowska
Round fire dampers with actuator - FDA2-12-M
Round fire dampers with actuator - FDA2-12-M
The FDA212 round fire dampers are designed for use in general ventilation systems to seal off smoke and fire between adjacent fire partitions. The fir...
PL-05-552 Wola Mrokowska
Air tight damper - DATL/DAT
Air tight damper - DATL/DAT
The DATL/DAT dampers are designed for cladding with up to 50 mm thick insulation. The DATL/DAT dampers are a good choice when the ductwork closure mus...
PL-05-552 Wola Mrokowska
EPP ventilation bend 43 mm thick - EPP-43-BPF-45
EPP ventilation bend 43 mm thick - EPP-43-BPF-45
Ventilation bends 45˚ made from expanded polypropylene (EPP). Bends are produced in diameters 125, 160 and 200 mm. The standard wall thickness is 43mm...
PL-05-552 Wola Mrokowska
Circular shut-off fire damper with thermal fuse - FDA-12-T
Circular shut-off fire damper with thermal fuse - FDA-12-T
The FDA12 round fire dampers are designed for use in general ventilation systems to seal off smoke and fire between adjacent fire partitions. The fire...
PL-05-552 Wola Mrokowska

The europages app is here!

Use our improved supplier search or create inquiries on the go with the new europages app.

Download in the App Store

App StoreGoogle Play