Продукти за gp27a (7)

Der Qualitätsmaßstab verfügt über Präzisionsfedern aus gehärtetem Stahl. Dies sichert eine verschleißfreie und dauerhafte Federung. Das Gelenk bleibt immer leichtgängig und exakt arretierbar. Durch die geringe Durchneigung der stabilen Glieder und das geringe Gewicht der Präzisionsfedern eignet er sich hervorragend für Hochmessungen. Der Nietkopf (Drehpunkt) der durch gehenden Nieten dreht auf einer Kunststoff scheibe, dadurch ist die Gelenkverbindung zusammen mit der gehärteten Feder auf Dauerbelastung ausgelegt. Die Maßstabglieder sind ohne seitliche Einfräsungen, deshalb kann eine gerade Anreißlinie gezogen werden. Die enganliegenden Glieder ermöglichen einen filigranen Werbedruck auf der gesamten Hochseitenfläche. Holzgliedermaßstab 2 m 10 Glieder Gelenke mit innenliegenden gehärteten Stahlfedern Glieder ca. 3,4 x 16 mm 100 Stück ca. 10,9 kg brutto.

The use of servo-hydraulic controls can significantly extend the range of applications for swivel motors. Larger loads can be slewed in a shorter time than is possible with purely hydraulic systems, where the damping travel is fixed. In conjunction with such a control system, the acceleration and braking behavior of the swivel motors can be specifically adapted to the requirements. This means that even fast and very precise movements with large masses can be safely mastered. We offer customized solutions for a wide range of applications. Our qualified team will be happy to advise you on design and realization. Specific torque [Nm/bar]:1,19 Operating pressure [bar]:200 Nominal torque [Nm]:238 Swivelling angle [ degrees° ]:250 Shaft end: (P) toothed shaft (Z) keyway key:P

PGD ​​2207

R134a is internationally recognizcd asone of the main refrigerant working substances to substitute CTC 12. It doesnot contain chlorine atom, gives no bad effects against ozonosphere and hasexcellent safety performances, such as noninflammability, non-explosiveability, non-toxicity, non-pungency, and non-corrosive ability. It is acolorless gas under ordinary temperature and a colorless & transparentliguid under the pressure of itself. As the substitute for crc 12, it is oftenused in the refrigerating systems of auto air conditioners, commercial ancindustrial purposes, and as the vesicant, it is used to produce theheat-protective material made of rigid plastics, and also to prepare otherblend refrigerants, such as R404A & R407C. SKU:TH675GL7X13690 Model:67010 Package Dimensions:18.25 x 12.32 x 10.75 inches Exterior:Steel, brass Voltage:12 Volts

Zuverlässige High Torque Sicherheitskupplungen für Schwerlastanwendungen ✓ Freies Auslaufen ✓ Lange Lebensdauer ✓ Wartungsfrei Lasttrennend Die EAS®‑HT ist eine formschlüssige, freischaltende Sicherheitskupplung nach dem Kugel-Senkungs‑Prinzip. Im Betrieb wird das eingestellte Drehmoment von der Nabe über den Druckflansch bzw. die Flanschnabe auf den Abtrieb übertragen. Bei Überschreiten des eingestellten Drehmoments (Überlastfall) rastet die Kupplung aus. Beim Ausrasten führen die Bolzen in den Überlastelementen eine axiale Bewegung (Hub) aus und bleiben in ausgerasteter Stellung. Nachlaufende Massen können frei auslaufen. Die Wiedereinrastung erfolgt manuell.

The output shaft of the HSH swivel motors has radial and axial hydrostatic bearings. Here, radially and axially arranged bearing pockets are supplied with pressurized oil via a separate pressure connection. As a result, the output shaft is centered radially and axially between liquid cushions and all metallic contact surfaces are permanently separated from each other by a thin liquid film. This eliminates wear caused by metallic friction in any operating state, even at zero speed compared to hydrodynamic plain bearings. In conjunction with highly dynamic control valves and angle of rotation sensors, these actuators are preferably used in controlled systems in which disturbance variables such as friction and the stick-slip effect must be reduced to a minimum. Furthermore, due to the lack of internal seals, they are ideal for test series with large numbers of load cycles where an interruption, e.g. due to the replacement of internal seals, is not permitted. Specific torque [Nm/bar]:2,05 Operating pressure [bar]:280 Nominal torque [Nm]:574 Swivelling angle [ degrees° ]:120

The output shaft of the HSH swivel motors has radial and axial hydrostatic bearings. Here, radially and axially arranged bearing pockets are supplied with pressurized oil via a separate pressure connection. As a result, the output shaft is centered radially and axially between liquid cushions and all metallic contact surfaces are permanently separated from each other by a thin liquid film. This eliminates wear caused by metallic friction in any operating state, even at zero speed compared to hydrodynamic plain bearings. In conjunction with highly dynamic control valves and angle of rotation sensors, these actuators are preferably used in controlled systems in which disturbance variables such as friction and the stick-slip effect must be reduced to a minimum. Furthermore, due to the lack of internal seals, they are ideal for test series with large numbers of load cycles where an interruption, e.g. due to the replacement of internal seals, is not permitted. Specific torque [Nm/bar]:32,80 Operating pressure [bar]:280 Nominal torque [Nm]:9184 Swivelling angle [ degrees° ]:120