Продукти за hdpe гранули (4)

Syntech HAG Stabiland Product consumption depends on the size of the void volume to be filled and on the expansive reaction that is triggered after mixing the two components in relation to the amount of water present. Can 21.5 kg [A] - Can 24.5 kg [B] - Kit: 1 Can 21.5 kg [A] + 1 Can 24.5 kg [B]

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Protech Balcony WV A solution based on special silane and siloxane resins in aqueous dispersion, being highly penetrating and transparent (colourless) for quickly, effectively and economically waterproof balconies, tiled terraces, concrete roofing, external stairs, and so on, without removing or impacting upon on the existing flooring. It does not change the appearance of the substrate on which it is applied nor alter its original degree of lubricity or breathability to water vapour. Application is swift, without requiring specialised labour or professional equipment. The treated flooring will be usable only 2 hours after application. Applying Protech Balcony WV is quick and easy – simply use a brush on clean and dry surfaces to resolve any seepage problems. The active substance penetrates quickly and deeply into the grouting, any cracks and porous points of the substrate. Upon contact with air, it causes a polymerisation reaction that perfectly and deeply seals and waterproofs every imperfection it encounters. The specific reactive polymerised siloxane molecule is stable over time and does not labilise. In accordance with the data sheet, the effectiveness of the product applied is normally more than 10 years on surfaces not subject to dynamic movements or structural and/or seismic damage. Should any new gaps or cracks appear after the first application of Protech Balcony WV, they can be easily resolved with a second application of the product. Given its intrinsically non-film nature, the product does not suffer damage, tear, crack, detach, deteriorate nor will it yellow over time due to the effects of UV rays (as naturally happens with epoxy and/or polyurethane treatments). The grouting treated with Protech Balcony WV is protected from mould, moss, lichen and other biodeterioration organisms. Rapid waterproofing of balconies, terraces, stairs, tiled surfaces, concrete and natural stone products, without having to demolish the existing flooring. It can also be used on vertical surfaces particularly exposed to weather and atmospheric conditions (tiles, plaster, exposed brick, etc.). The surfaces on which it is applied must be clean, free of stains, loose and crumbly parts, dust, and so on. If there are any joints between the tiles, they must be properly treated with a suitable acidic or alkaline detergent. To this end, we recommend the specific acid detergent Deterg-A, diluted with water at a ratio of 1:4. Rinse off the treated surfaces with running water. Any fragile and crumbly joints that have been removed, must be restored with cementitious putty offering high adhesion and deformability. To this end, we recommend using the specific waterproof and deformable two-component putty Stucco Balcony. Allow for the necessary time to pass (1–2 days) to allow the grouting to dry before applying Protech Balcony WV. The expansion joints that may be present, including those relative to the line connecting the tiled paving and the outer edge beam (normally made of granite or natural stone), will normally have to be sealed with high-elasticity polymeric materials. To this end, we recommend sealing with Protech Flex, supported by the installation of Filtene Fondogiunto and the particular polyurethane Protech Flex Primer. Pour small amounts of the product at a time then spread evenly across the entire surface with a rubberised brush or rubber blade until the substrate is complete impregnated with the waterproofing. Using a long bristle brush or sponge, apply Protech Balcony WV with particular care in the less accessible and most challenging areas (edges, skirting boards, corners, thresholds, hatches, fireplaces, drains, etc.). Allow the product to penetrate for at least 60 minutes. Remove excess product from all treated surfaces using a cloth wet with water. The average product consumption is around 0.15 kilograms/square metre of surface to be waterproofed, varying depending on the absorption of the substrate and the size of any joints. Normally, 1 kilogram of Protech Balcony WV is enough to treat surfaces from 5 to 10 square metres. Approximately 0.15 kilograms of Protech Balcony WV per square metre of surface to be treated – consumption may vary depending on the porosity of the substrate. Packaging: 2-liter can UM: €/l

Repar Tix HG SB Thixotropic, structural, fibre reinforced cement mortar, with compensated shrinkage, with high intrinsic water tightness, and extraordinary physical and mechanical characteristics: adhesion, compression resistance, flexural strength, abrasion resistance, etc. Perfect for remediation of structural works and articles in degraded concrete and very high-performance coatings. Repar Tix HG SB, in addition to normal manual application techniques, it is a structural mortar specially formulated for applications with pumping/spray machines (wet spritz-beton technique). Particularly optimized parameters are: rheology, thixotropy and workability of the product, which allow spraying operations with reduced wear of the mechanical parts and little waste on the ground. Rheoplastic, thixotropic, structural, composite cement mortar, based on special cements and selected siliceous aggregates, reinforced with a balanced mixture of READYMESH polypropylene fibres and calcium metasilicate microfibres, added with specific agents and a high content of silica fume. After hardening, it provides very high performance in terms of intrinsic water tightness, resistance to washing and hydrolysing, mechanical strength, abrasion and cavitation, anti-carbonation, chemical-physical stability, resistance to harsh atmospheric agents and to leaching water. It has three-dimensional fibre-reinforcement, provides high hold; it is dimensionally stable (compensated shrinkage). The product can be supplied in mono-component or two-component version. The product, in the monocomponent version, is mixed with water (approx. 16% of the weight of the bag). In the two-component version, the product is mixed by adding the 4.5 kg of component B. The two-component version increases adhesion to the support and reduces free shrinkage to air, especially in the initial hardening phases and in particularly hot climates, without modifying the physical-mechanical characteristics of the end product. Repairs and protective coatings of hydraulic works (pipelines, dams, tunnels etc.), marine structures and artefacts in critical situations: aggressive chemical-physical agents, leaching water, marine atmosphere, etc. Specific for shotcrete interventions in galleries, tunnels, rock walls, irrigation and hydraulic channels, piles and micropiles, diaphragms, etc. Application surfaces should be clean, free of soiling, crumbling and non-adhering parts, dust, etc., conveniently saturated with water until they reach the condition "saturated with dry surface". An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). The use of pumping/spraying machines specifically designed to be used with fibre-reinforced structural mortars is recommended. For the spraying of structural mortars such as Repar Tix HG SB, an effective and sometimes prolonged mixing of the product, which must take place upstream of the pumping circuit, is always recommended. For this reason, the use of “plaster sprayers” with volumetric water dosage is not recommended. Pour about 2/3 of the mixing water into the mixer, add Repar Tix HG SB and the remaining water; continue to mix until a homogeneous lump-free mixture is obtained. The mixing water should be about 16% of the weight of the bag. Addition of Bond HG to the mixing water, (approx. 0.5 litres per 25kg bag of product) in the single component version, allows further improvement in terms of adhesion, hold, impermeability, workability, modelling and deformation capacity. In the case of use of the product in the two-component version, pour component B (liquid) into the mixer, gradually adding component A (powder) and mixing until the lumps are completely eliminated. For high coating thicknesses, static requirements, monolithic requirements, etc., performed with Repar Tix HG SB, it is advisable to use suitable metal reinforcements (electro-welded mesh, cages, etc.), anchored to the support with Syntech Profix, GROUT MICROJ, Repar Tix G2. Approximately 18,5 kg/m² of Repar Tix HG SB for every centimetre of thickness to be implemented (approximately 1850 kg per cubic metre). Bag 25 kg - Pallet: 50 x (Bag 25 kg)